Additional Information
| Watts LP | 12000 |
|---|---|
| Amps LP | 50 |
| Watts NG | 10000 |
| Amps NG | 41 |
| Voltage Output | 120/240 Volt Single Phase |
| Voltage Regulation | Capacitor |
| Engine Brand | Honda |
| Fuel | LP/NG |
| Emissions | CARB/California, EPA Prime, EPA Standby |
| Dimensions | 40.15" x 31.73" x 30.37" |
| Weight | 502 lbs. |
| Assembled In | USA |
peter –
I would like to know why it will not start on auto when we lose power
Upvote if this was helpful (0) Downvote if this was not helpful (0) Watch Unwatch Flag for removal
Josie Krugerud –
Hello Peter, we are sorry to hear you are having issues with your generator. Please contact our Service Department, 507-357-6831 or service@wincogen.com, and they will be able to assist you.
Upvote if this was helpful (0) Downvote if this was not helpful (0) Flag for removal
Question
Greg Raver –
What is the HP rating of the GX690 engine on the PSS12H generator? I’m surprised that it isn’t mentioned anywhere that I can find on this site.
Upvote if this was helpful (0) Downvote if this was not helpful (0) Watch Unwatch Flag for removal
Josie Krugerud –
Hello Greg,
The horsepower is 22.1 for this engine.
Upvote if this was helpful (0) Downvote if this was not helpful (0) Flag for removal
Karl –
Is there an app to tell me if it is running or not?
Upvote if this was helpful (0) Downvote if this was not helpful (0) Flag for removal
Josie Krugerud –
Hello Karl, At this time we do not have an app compatible with the DSE3110 controller that used in this model.
Upvote if this was helpful (0) Downvote if this was not helpful (0) Flag for removal
Question
Greg –
Is there a generator auto start available that will automatically start my PSS12H2W when the water pressure drops on my well pump pressure tank?
Upvote if this was helpful (0) Downvote if this was not helpful (0) Watch Unwatch Flag for removal
Josie Krugerud –
Hello Greg,
There is a way by using a float switch that would wire to the 2-wire control.
Upvote if this was helpful (0) Downvote if this was not helpful (0) Flag for removal
Question
Christopher Holt Jr –
how long of a run time on LP
Upvote if this was helpful (0) Downvote if this was not helpful (0) Watch Unwatch Flag for removal
Josie Krugerud –
Hello Christopher, It all depends on your tank. The LP fuel consumption is 2.1 GAL/HR – 194,000 BTU/HR.
Upvote if this was helpful (0) Downvote if this was not helpful (0) Flag for removal
Bob Post –
Guess I should have specified…approximately how many hours be fore a major rebuild/refurbishment is required?
Upvote if this was helpful (0) Downvote if this was not helpful (0) Watch Unwatch Flag for removal
Dale Riebel –
Bob, please contact our Technical Support Department at 507-357-8334 or service@wincogen.com.
Upvote if this was helpful (0) Downvote if this was not helpful (0) Flag for removal
Question
Wade Maner –
What is the recommended BTU size regulator? This generator will be mounted on a trailer as a portable standby package using two 20 lb propane tanks on an auto changeover configuration. The regulator will be approximately 8 – 10 feet from the generator. 1” black steel pipe is being run from the regulator to the genset.
Upvote if this was helpful (0) Downvote if this was not helpful (0) Watch Unwatch Flag for removal
Dale Riebel –
Wade, please follow the guidance in our installation and operation manual. It is on product page if you scroll down and click on the “downloads” tab. If you need further assistance please call or email our Technical Support Department @ 507-357-8334 or service@wincogen.com.
Upvote if this was helpful (0) Downvote if this was not helpful (0) Flag for removal